![\"\"](\"http:\/\/3.bp.blogspot.com\/-NazVX9DLdTs\/Vj4TrtCPH3I\/AAAAAAAAAfs\/H8mNEw8mDTY\/s1600\/20151107_082926.jpg\")
<\/p>\n
I wanted to reprogram the chip so I could use the kit as a stopwatch\/timer instead of a regular clock<\/a>.\u00a0 Of course I could have bought a programmer to do the job, but reading the chip’s data sheet it seemed straightforward to do the programming with an Arduino – and I thought it would be a fun project to do that.<\/p>\n The chip is programmed a byte at a time by setting up each byte on 8 of the chip’s I\/O lines and then pulsing some of the other I\/O lines to ‘burn’ the byte to flash memory and move on to the next byte to be programmed.\u00a0 You can also read the existing program out of a chip (unless a read-protect bit has been set) and there are special ways of pulsing the I\/O lines to erase the whole chip and so on.<\/p>\n The only tricky thing is that one pin has to be raised from the nominal operating voltage of five volts up to twelve volts during programming – the challenge was working out the easiest way to do this using an Arduino.<\/p>\n So I decided to use an Arduino Mega 2560 for this project.\u00a0 A Uno doesn’t have quite enough I\/O to do the job properly, and the Mega 2560’s double row of I\/O pins makes routing the connections to the chip simple as the chip can sit directly over the double-row connector.<\/p>\n I decided to use a charge pump (voltage multiplier) running off the Arduino’s five volts to generate the programming voltage – that seemed cleaner than needing a separate twelve volt supply.\u00a0 It just uses a few diodes and capacitors and relies on the Arduino pulsing some of its I\/O lines to drive the voltage multiplier.\u00a0 A couple of zener diodes clip the voltage down to exactly 5V or 12V and a couple of transistors, also switched by the Arduino, select between either of those voltages or 0V to drive the pin on the chip.<\/p>\n I designed a PCB using the free KiCad package.\u00a0 Here’s a .pdf<\/a> of the circuit diagram, and here is what KiCad produces as a picture of the design.\u00a0 In the picture it looks like the chip to be programmed is soldered straight into the board, but of course in reality a ZIF socket is fitted in that position so that the chip(s) you are programming can be quickly swapped.<\/p>\n Here are a couple of snaps of the prototype board.\u00a0 You can see I didn’t bother to crop back the board edges!<\/p>\n![\"programmer3D\"](\"https:\/\/ceptimus.co.uk\/wp-content\/uploads\/2016\/02\/programmer3D-283x300.gif\")
<\/a>That picture wrongly shows the tracks on the top of the board – I design them that way for home production as the transfer process mirror-images the tracks so that they’re correct for the back of the board.\u00a0 If you fancy making one of your own, it would be quite straightforward to\u00a0 do it on strip board – like I say most of the pins of the chip just connect direct to the Arduino pins that the chip sits over.\u00a0 If you want to etch your own PCB, here is a .pdf of the mask<\/a>.<\/p>\n![\"top\"](\"https:\/\/ceptimus.co.uk\/wp-content\/uploads\/2016\/02\/top-300x268.jpg\")
<\/a>![\"back\"](\"https:\/\/ceptimus.co.uk\/wp-content\/uploads\/2016\/02\/back-209x300.jpg\")
<\/a>And this is what it looks like when docked on top of the Arduino Mega 2560.<\/p>\n![\"topDocked\"](\"https:\/\/ceptimus.co.uk\/wp-content\/uploads\/2016\/02\/topDocked-300x150.jpg\")
<\/a>![\"backDocked\"](\"https:\/\/ceptimus.co.uk\/wp-content\/uploads\/2016\/02\/backDocked-300x249.jpg\")
<\/a>So that’s about it for the hardware.\u00a0 I’ll make a separate post about the Arduino sketch that does the work of programming the chip, and the PC program that talks to the Arduino to send and receive hex files.<\/p>\n